Drop-in, EDM machined parts provide improved performance at a fraction of the cost of expensive hand fitting. Everything you need to produce a light, crisp trigger for the 10/22. EDM matched hammer and sear, overtravel adjustable aluminum trigger, two hammer and two trigger shims, extra power hammer spring, extra power disconnector spring and extra power trigger return spring. Recoil buffer included. Mfg: Power Custom SPECS: Black aluminum trigger. Other parts, steel, matte blue finish. Heat treated to Rc 56-58. Includes assembly pin and instructions.
Impact-resistant, cartridge tray extends your rifle’s magazine capacity by replacing the factory floorplate. Injection-molded from high-strength, 60% glass-reinforced nylon for superior durability and reliable function in all conditions. Drop-in fit, requires use of your factory magazine spring, follower, and hinge pin. Short Action model increases the standard magazine capacity of .223-based calibers up to nine rounds. Removable cartridge stop lengthens the tray to accept .308-based cartridges, and increases magazine capacity from four to seven rounds. Long Action model increases the standard magazine capacity of .30-06-based calibers from four to five rounds. Models available for Rem Mfg: Tactical Components, Llc. SPECS: Glass-reinforced nylon, black. Rem. 700 – Short Action: 3-5/8″ (8.6cm) long, 1″ (2.5cm) wide, 3/4″ (1.9cm) high. Long Action: 4-5/8″ (12cm) long, 1″ wide, 1-1/8″ (3cm) high. Weatherby Vanguard/Howa – Short Action: 3-1/8″ (7.9c
Machined steel, five-port flash suppressor effectively controls muzzle flash to minimize shooter exposure in both daytime and low-light situations. Ports are located along the top of the suppressor and bottom is solid to reduce dust printing when shooting prone. Mfg: Dpms Firearms Llc SPECS: Machined steel, matte black. 1.75″ (4.4cm) long, 7/8″ (2.2cm) O.D. 1/2″-28 tpi. Requires peel washer (not included) for proper indexing.
Easy-to-build kits contain all the components needed to assemble a tactical charging handle that aids in fast action drills, efficient jam clearing, and smooth operation. All kits are built around a stripped DPMS factory charging handle machined to stringent mil-spec standards for proper fit and dependable function. Each kit also comes with latch spring and roll pin. Badger kit features an oversized latch that’s easy to find and operate with the left hand. Badger GEN II kit comes with a mid-sized latch for those seeking a larger grasping surface that won’t interfere with optics. M&A Ambi kit includes a large, extended latch lever that’s easy to grab and allows rapid ope Mfg: Brownells SPECS: Aluminum charging handle, matte black finish. Badger Steel latch, matte black. Latch approx. 1 1/2″ (3.8cm) long, 5/8″ (1.6cm) high. Badger Gen II Steel latch, matte black. Latch approx. 1 1/4″ (3.2cm) long. M&A Ambi Aluminum latch, mat
Cushioned rubber or nylon outer skin provides non-slip, shooting comfort; internal fiberglass body gives solid support, is lightweight and easy to carry. Fully-inletted for a drop-in fit; models available to fit either factory standard barrels (S/B) or nominal .920″ diameter bull barrels (B/B). Straight comb; wide, varmint-style forend with finger grooves, cobblestone finish on grip and forend; dual palm swells and recurve pistol grip make this stock as comfortable to shoot as it is practical. Includes rubber recoil pad, and front and rear sling studs. Mfg: Hogue SPECS: Fiberglass with Nylon or Rubber covering, black. 29″ (73cm) long, 13 3/4″ (35cm) length of pull, 1 1/4″ (2.8cm) drop at heel, 1.9 (.86kg) wt. fits Ruger 10/22.
Give your Remington bolt rifle a performance lift with these easy to install springs. Reduced power (RP) trigger spring helps lower felt trigger pull for better, more consistent accuracy. Mfg: Wolff SPECS: Spring steel. Fits Rem. 700/721/722.
5 sling attachment points Storage compartment for batteries or parts Mil-spec reinforced polymer composite Fits any weapon that accepts M-4/AR15 style stocks Patented system reduces recoil and muzzle rise for improved control during rapid and full auto fire Mfg: The Mako Group SPECS: Recoil-reducing collapsible stock, Fits AR-15 style rifles, 5-sling attachment points, 2 QR attachment points, Battery compartment, Rubber buttstock.
Reliable, easy-to-install, upgrade kits replace some or all of the factory trigger components to deliver match-grade performance in your rifle. Specially designed, system (except Mauser 98) moves the sear engagement point to a precise location for more leverage that lightens pull weight. Fewer working parts help eliminate malfunctions caused by moisture and freezing temperatures. Precision machined and polished engagement surfaces help minimize drag for smooth, crisp let-off. All models use the factory safety without alteration. Drop-in installation. Polished sear and trigger lever, plus a reduced power return spring smoothes trigger movement and lightens pull to 2 pounds. Adjustments for se Mfg: Jard SPECS: Steel, black matte or polished silver finish. 2 lb. pull weight. MK II – Fits Ruger M77 Mark II. Will not fit Target (VT) models. 77/22 & 77/17 – Fits Ruger 77/22, 77/22 WMR, and 77/17.
